Section 2 - Water

Press Enter to show all options, press Tab go to next option



City of Glendora Standard Designs & Specifications for Public Works construction can be viewed, downloaded and printed from this site. 

Index - Water  
S.D. & S. No. 2.00 Standard Construction Notes for Water Improvements
S.D. & S. No. 2.01 Flushing/Disinfecting Procedures for New Water Main Installation
S.D. & S. No. 2.03 Hydrostatic Testing Procedures for New Water Main Installations
S.D. & S. No. 2.04 Approved Materials for Fire Service Connections, 4"-10"
S.D. & S. No. 2.05 Approved Materials for 1", 1 1/2", 2" Services
S.D. & S. No. 2.07 Notice of Change Approval
S.D. & S. No. 2.08 Thrust Block Requirements for Ductile Iron Mainline
S.D. & S. No. 2.09 Fire Hydrant Assembly - Type I
S.D. & S. No. 2.10 Fire Hydrant Assembly - Type II
S.D. & S. No. 2.11  Air/Vacuum Release Valve Assembly, 1" for Ductile Iron Mainline
S.D. & S. No. 2.12 Protective Cover - Type I
S.D. & S. No. 2.13 Water Meter Installation Policy Installation and Scheduling Requirements
S.D. & S. No. 2.14 Meter Conduit Requirements for AMR Installations
S.D. & S. No. 2.16 Valve Box Assembly - Type I, Type II for Use in Concrete Surfaced Areas (Low speed vehicular traffic only)
S.D. & S. No. 2.17 Valve Box Assembly - Type III for Use in Asphalt Surfaced Areas
S.D. & S. No. 2.18 Standard 2.17 - Advisory Note Case II Advisory Note for Use on Improvement Plans
S.D. & S. No. 2.19 Pressure Connection, 4" - 10" from Steel to Ductile Iron Mainline
S.D. & S. No. 2.20 Blow Off Assembly, 1-1/2", 2" for Steel/Ductile Iron Mainline
S.D. & S. No. 2.21 Flushing/Sampling Connection for New Main Construction
S.D. & S. No. 2.22 Double Check Valve Assembly - Type I for Fire Service Connections, 4" - 10"
S.D. & S. No. 2.23 Test Plate Installation - Type I for New Main Construction
S.D. & S. No. 2.24 Protective Post - Type I
S.D. & S. No. 2.25 Service Assembly, 1" Copper for Steel/Ductile Iron Mainline
S.D. & S. No. 2.27 Service Connection, 1", 1 1/2", 2" for Steel Mainline
S.D. & S. No. 2.28 Meter Installation, 3/4", 1" for New Construction
S.D. & S. No. 2.29 Service Assembly, 1-1/2", 2" Copper for Steel/Ductile Iron Watermain
S.D. & S. No. 2.30 Minimum Installation Requirements for Backflow Prevention Devices
S.D. & S. No. 2.31 Service Lateral Grade Adjustment for 1-1/2", 2" Copper Service Assembly
S.D. & S. No. 2.32 Test Plate Installation - Type II for New Main Construction < 100 Feet
S.D. & S. No. 2.33 Flushing/Testing Protection for New Main Construction
S.D. & S. No. 2.34 Flushing/Sampling Connection for New Main construction < 100 Feet
S.D. & S. No. 2.35 Water Quality Testing Sequences for New Main Construction
S.D. & S. No. 2.36 Water Quality Testing Sequences Supplemental Chart
S.D. & S. No. 2.37 Approved Service Connection for Residential Service
S.D. & S. No. 2.38 Approved Service Connection for Commercial Service
S.D. & S. No. 2.39 1" Service Installation/Tie In for Single Service Replacement
S.D. & S. No. 2.40 1" Service Installation/Tie In for Dual Service Replacement
S.D. & S. No. 2.41 Service Protection for Site Demolition
S.D. & S. No. 2.42 Service Manifold Assembly for Multiple 1" Service Assemblies
S.D. & S. No. 2.43 Tie In/Test Installation for Ductile Iron Main Construction
S.D. & S. No. 2.44 Blow Off/Flushing Assembly for Use with 2" Service Assembly
S.D. & S. No. 2.45 Protective Cover - Type II for 2" - 6" Air Vacuum Release Assembly
S.D. & S. No. 2.46 Air Vacuum Release Assembly, 2" for Ductile Iron/Steel Mainline
S.D. & S. No. 2.47 Sample Station Assembly, 1" for Bacteriological Sampling


As an alternative, a full set of Standard Designs & Specifications can be purchased at the Public Works Department public counter for $25. This set can be kept as a master copy and updated by downloading and printing only those drawings that have been revised. The Standard Designs & Specifications may be updated from time to time as required, without prior notice. It is the responsibility of interested parties to keep their master copies of these documents current. It is the contractors' responsibility to obtain and maintain up-to-date copies of the standard drawings while performing any work in the Public Right-of Way.

For additional information please contact:

City of Glendora – Public Works Department
(626) 914-8246
Monday – Thursday 8:00 AM – 5:00 PM

Free viewers are required for some of the attached documents.
They can be downloaded by clicking on the icons below.

Acrobat Reader Download Acrobat Reader Flash Player Download Flash Player Windows Media Player Download Windows Media Player Microsoft Silverlight Download Microsoft Silverlight Word Viewer Download Word Viewer Excel Viewer Download Excel Viewer PowerPoint Viewer Download PowerPoint Viewer